Search the Community
Showing results for tags 'remotesensor'.
Along with the Logitech Arx integration, we've also come up with a new LCD module that basically acts as a web server. You can use your main computer to run AIDA64 on it and maintain its built-in web server, and you can use your other computers or mobile devices to monitor your main computer's status remotely, using nothing but a web browser. You can activate it in AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / RemoteSensor. Once you activated it, you can enter the IP address in virtually any web browsers to connect to the RemoteSensor. You can check the primary IP address of your computer on the Computer / Summary page in AIDA64. If it is e.g. 192.168.1.123, then enter the following in the address bar of your web browser: http://192.168.1.123 Or, in case you use a different TCP/IP port than the default http port of 80, then enter the address like this: http://192.168.1.123:8080 (if you use a TCP/IP port of 8080) Or, in case you try to use a web browser on the same computer where AIDA64 is running, you can simply use "localhost" instead of the IP address, like this: http://localhost Once you did that, you should see the AIDA64 splash screen in your web browser. It will provide you with information on the resolution that you need to use to get the most out of the LCD layout designer. On iOS devices the default setting should be close to the actual value to use, while on Android and other devices it may not match at all, so you need to change both the width and height. Please note that the Preview Resolution usually will not match the native screen resolution of your device. It's not a problem at all, and that discrepancy is due to the way web browsers manage the pixels of your screen, so don't be surprised that e.g. an iPhone 5 would report a Preview Resolution of 980 x 1360 pixels After the Preview Resolution is updated on the AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD page, you can use the same LCD layout designer that you would use for other LCD devices or the SensorPanel. Known issues and limitations: 1) Graphs and gauges are not implemented yet. We're planning to add them in the next few weeks. 2) RemoteSensor uses HTML5 SSE (Server-Sent Events) to refresh the web page, without having to reload it all the time. SSE is supported by almost all major web browsers, including Android Browser, BlackBerry 10 Browser, Chrome, FireFox, Opera, and Safari. However, it is sadly not yet supported by Internet Explorer. AIDA64 implements a trick to get around that limitation, but it sometimes will result in a mixup of the browser. If you notice that after changing the LCD layout in the AIDA64 Preferences, a strange log replaces the LCD layout in your browser, just refresh the web page. Hopefully Microsoft will finally implement SSE support in Internet Explorer 12 3) In order to prevent your mobile device from going to sleep while having the web browser open, you may need to install special apps on your mobile device. RemoteSensor has absolutely no control over the power management behavior of your mobile device. In case this is a deal breaker for you, and you've got a Logitech Gaming hardware, consider using Logitech Arx instead of the RemoteSensor. You can try the RemoteSensor in the following new AIDA64 beta update: http://www.aida64.com/downloads/latesta64xebeta Please let us know how it works on your mobile devices Thanks, Fiery
When I go to setup the Remote sensor panel and setup LCD items the window on the view is empty and nothing is displayed. I'm on Windows 10 May Update on the latest Aida64. I even tried using the latest beta with no luck. Here is a screenshot. This is happening on two different systems. One is an older machine with Intel 6700K the other is new with an Intel 8700K so I don't think it's hardware related. They even have different motherboards. Infact both these system used to have this working previously but I wiped both of them and did a fresh install of Windows 10 May.
I am still a aida64 learner. =.= like,it was about the LCD settings, I planned to used my iPad 6 as a to detecting the computers' working performance but unfortunately after I done the settings in the "remotesensor" like the picture below, then I double checked the Resolution setting again， and use 1080*1920 to check whether it can be shown on my another screen or not, but it still doesn't work QAQ, things shown in the browser are not in a right order as set before, please help me!!!
First, I want to give the developers of this software a thumbs up for the work they do with this software and mostly for the good care that they give to the comunity. I really apreciate how fast you give answers to all the questions posted. Thank you for that! The reason that I`ve bought the software is its great flexibility in outputing the sensor values to different displays. In that regard, after reading some of the post, I understand that you try to follow the market by giving atention to RemoteSensor, more than the Sensor Panel. If I am correct, I would like to know if you could implement more control over this, like allowing html and css input so that more interesting ways of displaying the values could be use. I would like to have some conditional formating options ( like changing the color of text at certain thresholds, etc., similar to what could be done with LCDhost for Logitech G19s keyboards). If you have other sugestion about the way I could go to achieve that, please let me know. I am also exploring Roccat Power-Grid, looks much more promising than Arx Control from Logitech. It would be dificult to offer suport for that? I think that would help alot in doing fast verry interesting monitoring grids that anyone could use. From what I have red in the pdf help for the SDK, a dll that would give acces to all Aida64 sensors should be easy enough to write ( for someone with experience, meaning not me ). Thank you!