Jump to content
AIDA64 Discussion Forum

Recommended Posts

This is a more general question, but the need for it is in connection with AIDA64 using for G19's LCD display.

When starting the PC the drivers and software are starting in this order:AIDA64, FRAPS and one of the very last is the newly installed LGS (Logitech Gaming Software) for G19 and other Logitech devices.

So AIDA64 has an error and cannot display his info on the panel, because at the time that AIDA64 driver is automically started no G19 driver loaded. I can only terminate AIDA64 (and FRAPS and similar untilities) and start again: Then everything works.

Any chance, how the order of automtacally starting drivers can be set in msconfig on XP (and how to do on Win7)?

Share this post


Link to post
Share on other sites

When you've got a Logitech LCD keyboard, there're two methods of starting AIDA64 at Windows bootup. First is the classic method of using the option in AIDA64 Preferences / General page, which starts AIDA64 from either the Registry's relevant Run section (under Win2000/XP), or using the Task Scheduler (of Vista/Win7/Win8). Using this startup method may cause issues when bootup order of software and drivers get mixed up.

Second method is using the Logitech LCD Manager to launch AIDA64 when it starts up the applets. I suppose in your case this option should be used, and the classic startup method in AIDA64 Preferences should be disabled. That way LCD Manager will launch AIDA64 when it initializes the LCD applets.

Regards,

Fiery

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Similar Content

    • By beada
      BeadaFrame Display Kit is an ARM Cortex-A7 development platform which bundled with a 7" TFT LCD Display. It can be powered and communicated with PC Host by a single Micro USB cable. Currently we use it as a secondary PC monitor for display of hardware status through Remote Sensor LCD.
      The question is --  is there any way to implement it as a native support of AIDA LCD screen? We are running Debian Stretch on the ARM Cortex-A7 core.


       
      And more details of this display kit:
      CPU
      NXP/Freescale ARM Cortex-A7 i.MX6ULL
      RAM
      512MB DDR3L
      Storage
      16GB/32GB eMMC
      Connectivities
      1 x WIFI 802.11 b/g/n module(AP6212) 1 x USB 2.0 Host(Type A) 1 x USB 2.0 OTG(Micro-USB) Display
      7.0" TFT LCD: 800x480 (AT070TN92) , w/ touch and bezel
      On Board Resources
      Reset Circuit with reset button 1 x Power select jumper 1 x Boot select jumper 1 x USER LED Dimension
      188 x 118 x 35(mm)
      Operating System
      Debian Stretch
      Consumption
      5V/350mA
    • By Shaman
      Dear all,
      I am trying to figure out the best option for a small (max 7'') external screen to use with SensorPanel.
      I find lots of options on eBay that I suppose are all viable (e.g., https://www.ebay.co.uk/itm/7inch-HDMI-LCD-H-with-case-1024x600-IPS-Capacitive-Touch-Screen-Audio-Output/133067577890).
       
      What I am unsure at the moment:
      - Is the quality/resolution of the screen important?
      - Is touch input needed/used?
      - Is there any difference (limitations) between the three available options (using an HDMI connected screen, a USB connected one and/or an affordable Android tablet)? 
       
      Any input would be appreciated. Thank you in advance!
       
      Best,
      S
    • By Ventilator
      Would be nice if you could rotate output 90 degrees in AIDA 64 LCD config for Logitech ARX.
      This, so you can get tablet mode.
       
    • By Roy
      Hi,
      it would be nice if there was the possibility to send sensor values unformatted as a number or percentage, via a serial port.
      Similar to the LCD displays, only without formatting, or pure numbers with separators.
      Together with a small GUI.
      Background is the simple evaluation of the data with a microcontroller and display in different ways.
      I imagine not only LCD or OLED, but rather seven segment display, nixi tubes or an analog pointer display. That would create a lot of possibilities.
×
×
  • Create New...