Jump to content
AIDA64 Discussion Forum

Recommended Posts

On 2017/6/6 at 10:59 PM, Fiery said:

AIDA64 does support remote connections through WiFi via the RemoteSensor module, but I don't think you'd have a http client on your device :)  Let us know more about the protocol we'd need to use to talk to the mentioned ESP8266 MCU.

Thanks for your reply, I think the performence of ESP8266 is too low to make http client work. Frames transmit to ESP8266 via WIFI should work but the bandwitdh consumes high. Another way I think is learn from AX206, transfer graphics by differentia. Recently, I am working on ESP8266 and ILI9488 but no luck, I think 480x320 will provide more display area, I will keep on it and think about the transfer protocol. Thank you for your help.

Share this post


Link to post
Share on other sites
On ‎2018‎. ‎01‎. ‎20‎. at 6:53 PM, Ataulf said:

Would it be possible to add support for Hama's line of photo frames (just like the now discontinued Samsung displays):

https://www.hama.com/product-showcases/digital-picture-frames

Thanks a million :-)

As far as I can understand, that picture frame isn't capable of transferring full bitmap frames from a computer to the digital picture frame.  So it cannot be supported by AIDA64 or any other monitoring software.

Share this post


Link to post
Share on other sites

is there a way to display pc sprecs on "trekstrore surftab breeze 7.0 quad" with android 4.4.2 kitkat? odospace will not find this device on pc. but my samsung woks just fine...

Share this post


Link to post
Share on other sites
On ‎2018‎. ‎03‎. ‎30‎. at 2:22 PM, hybsen said:

is there a way to display pc sprecs on "trekstrore surftab breeze 7.0 quad" with android 4.4.2 kitkat? odospace will not find this device on pc. but my samsung woks just fine...

We're not the developers behind Odospace, so cannot help you with that.  You can however use the RemoteSensor feature with any Android tablets basically:

 

Share this post


Link to post
Share on other sites
On ‎10‎/‎9‎/‎2018 at 8:29 AM, btmouse said:

RoboPeak迷你USB显示屏

http://www.robopeak.com/blog/?p=406

希望得到支持

We've ordered a sample of that display, and will implement support for it as soon as it arrives.  I'll let you know in this topic when we have a new AIDA64 beta build that you can test on the RoboPeak display.

Share this post


Link to post
Share on other sites
33 minutes ago, Fiery said:

我们订购了该显示器的样品,并在它到货时立即实施支持。当我们有一个可以在RoboPeak显示器上测试的新AIDA64 beta版本时,我会在这个主题中通知你。

a happy decision
 

Share this post


Link to post
Share on other sites
On ‎6‎/‎8‎/‎2017 at 7:46 PM, awayfar said:

Thanks for your reply, I think the performence of ESP8266 is too low to make http client work. Frames transmit to ESP8266 via WIFI should work but the bandwitdh consumes high. Another way I think is learn from AX206, transfer graphics by differentia. Recently, I am working on ESP8266 and ILI9488 but no luck, I think 480x320 will provide more display area, I will keep on it and think about the transfer protocol. Thank you for your help.

Is it possible to somehow stream the bitmap data from a TCP/IP port (of the WiFi layer) into the display?

Also, here are 2 projects that may be helpful for you:

https://diyprojects.io/esp8266-web-client-sending-data-jeedom-tcp-ip-wireless-json-api/

https://www.dfrobot.com/blog-782.html

Share this post


Link to post
Share on other sites
19 hours ago, Fiery said:

Is it possible to somehow stream the bitmap data from a TCP/IP port (of the WiFi layer) into the display?

Also, here are 2 projects that may be helpful for you:

https://diyprojects.io/esp8266-web-client-sending-data-jeedom-tcp-ip-wireless-json-api/

https://www.dfrobot.com/blog-782.html

aida64  it’s perfect if it’s compatible with the Arduino board.
 

Share this post


Link to post
Share on other sites
2 hours ago, btmouse said:

aida64  it’s perfect if it’s compatible with the Arduino board.
 

It isn't compatible, but it's mostly because AFAIK it's not possible to write a generic communication protocol for LCD displays that are connected to a PC USB port via Arduino.

However, it should be possible to write an Arduino program (sketch) to emulate an existing LCD protocol to make the Arduino+LCD combo compatible with an existing AIDA64 LCD module.

Share this post


Link to post
Share on other sites
7 hours ago, btmouse said:

how to use custom character display ?

This will make the LCD look cool !

AIDA64 doesn't support custom characters for external LCD displays.

Share this post


Link to post
Share on other sites
1 hour ago, btmouse said:

oled support custom characters displays?

for example: ER-OLEDM032

ER-OLEDM032 is a graphical (dot matrix) display that can display any kind of graphics.  With such displays you have way more flexibility than with alphanumeric (character) displays that can only display pre-defined or custom characters.

Share this post


Link to post
Share on other sites
On ‎10‎/‎10‎/‎2018 at 1:00 PM, btmouse said:

a happy decision
 

We've opened a separate topic for RoboPeak:

 

Share this post


Link to post
Share on other sites
5 minutes ago, btmouse said:

i will look for more possible LCDs for you.
 

Thank you.  Although, it would be best if you owned those displays and really wanted to use AIDA64 on them ;) 

Share this post


Link to post
Share on other sites
8 minutes ago, Fiery said:

Thank you.  Although, it would be best if you owned those displays and really wanted to use AIDA64 on them ;) 

i have a Samsung SPF-87h and lcd2usb 2004 used for aida64. :wub:

and

i have an idea
if  have two of the same models lcd,installed in  case different places,e.g. : two 1602 LCD
Can they work at the same time? 

i don't know if you can understand me.
my english is bad
can only rely on google translate

Share this post


Link to post
Share on other sites
19 minutes ago, btmouse said:

i have a Samsung SPF-87h and lcd2usb 2004 used for aida64. :wub:

and

i have an idea
if  have two of the same models lcd,installed in  case different places,e.g. : two 1602 LCD
Can they work at the same time? 

i don't know if you can understand me.
my english is bad
can only rely on google translate

I meant if you request us to add support for a currently unsupported display, it is best if you already own (or plan to own in the near future) the display :)  It's not a huge problem if you don't, for example if you only want to purchase a display when it's already supported by AIDA64.  Fortunately implementing support for RoboPeak wasn't too difficult, but there are a lot more challenging devices.

Multiple displays of the same kind is only supported for a few displays out there right now.  You can use:

  • two Razer LCDs
  • two AlphaCool LCDs
  • three picoLCDs
  • three Saitek LCDs
  • three Trefon LCDs
  • three Cwlinux LCDs
  • three YoctoPuce OLEDs
  • three Crystalfontz LCDs
  • three Aquaero LCDs
  • three LCDInfo LCDs
  • three Phidget LCDs

We only enable more than one LCD support (of the same kind) per request, since most users only have one display from a particular vendor.  You can however mix any number of displays when they're different kind.  For example, you can use one LCD2USB, one Samsung SPF, one Matrix Orbital GX, one RoboPeak, and one EastRising (so 5 displays total, but it can be even more) simultaneously with AIDA64.  The only difficulty you will experience with such a setup is the delays in poll rate due to the enermous USB traffic :)  BTW, just as with multiple devices support, hot-plug support and rotation support are also only enabled for a few devices.  But they can be enabled for other devices per user request.

Share this post


Link to post
Share on other sites

btmouse, beada:  Please use this forum for English discussion only.  Use private messaging to communicate in your native language. Thank you!

btmouse:  We're working together with beada to implement native support for their existing hardware in AIDA64.  Till then RemoteSensor is the way to go:

 

Share this post


Link to post
Share on other sites
On 2018/11/30 at PM6点43分, Fiery said:

btmouse,beada:   请使用此论坛进行英语讨论。使用私人消息以您的母语进行交流。谢谢!

btmouse:   我们正在与beada合作,为AIDA64中的现有硬件实现原生支持。直到RemoteSensor才是最佳选择:

 

I am sorry,
Next time

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Similar Content

    • By beada
      BeadaFrame Display Kit is an ARM Cortex-A7 development platform which bundled with a 7" TFT LCD Display. It can be powered and communicated with PC Host by a single Micro USB cable. Currently we use it as a secondary PC monitor for display of hardware status through Remote Sensor LCD.
      The question is --  is there any way to implement it as a native support of AIDA LCD screen? We are running Debian Stretch on the ARM Cortex-A7 core.


       
      And more details of this display kit:
      CPU
      NXP/Freescale ARM Cortex-A7 i.MX6ULL
      RAM
      512MB DDR3L
      Storage
      16GB/32GB eMMC
      Connectivities
      1 x WIFI 802.11 b/g/n module(AP6212) 1 x USB 2.0 Host(Type A) 1 x USB 2.0 OTG(Micro-USB) Display
      7.0" TFT LCD: 800x480 (AT070TN92) , w/ touch and bezel
      On Board Resources
      Reset Circuit with reset button 1 x Power select jumper 1 x Boot select jumper 1 x USER LED Dimension
      188 x 118 x 35(mm)
      Operating System
      Debian Stretch
      Consumption
      5V/350mA
    • By Shaman
      Dear all,
      I am trying to figure out the best option for a small (max 7'') external screen to use with SensorPanel.
      I find lots of options on eBay that I suppose are all viable (e.g., https://www.ebay.co.uk/itm/7inch-HDMI-LCD-H-with-case-1024x600-IPS-Capacitive-Touch-Screen-Audio-Output/133067577890).
       
      What I am unsure at the moment:
      - Is the quality/resolution of the screen important?
      - Is touch input needed/used?
      - Is there any difference (limitations) between the three available options (using an HDMI connected screen, a USB connected one and/or an affordable Android tablet)? 
       
      Any input would be appreciated. Thank you in advance!
       
      Best,
      S
    • By Ventilator
      Would be nice if you could rotate output 90 degrees in AIDA 64 LCD config for Logitech ARX.
      This, so you can get tablet mode.
       
    • By Roy
      Hi,
      it would be nice if there was the possibility to send sensor values unformatted as a number or percentage, via a serial port.
      Similar to the LCD displays, only without formatting, or pure numbers with separators.
      Together with a small GUI.
      Background is the simple evaluation of the data with a microcontroller and display in different ways.
      I imagine not only LCD or OLED, but rather seven segment display, nixi tubes or an analog pointer display. That would create a lot of possibilities.
    • By Wampo
      Hey Aida Team,
      i have some issues with this Adafruit LCD wich is recomended. On the two Pictures you can see what aida should do and what can i see on the Display. The First line is completely erased and the screen is flickering. The Adafruit Backpack is set to 20x4 LCD. When the Display is updating you can see the right setting for a millisecond.
      But if i change the LCD Setting in AIDA to 16x2, and leave the Backpack in 20x4 mode,  the Screen isn flickering and the first line is there. I think you got a little problem with the 20x4 Driver. I have Searched for the code but i cant find it, to edit it if i found the failure. 
       
      Please give me response for this BUG. I have extra ordert this overpriced 50€ LCD for it. 
      Greetings Daniel from Germany


      VID_20181129_160917.mp4
×
×
  • Create New...