I was running a stress test on a my new Pc and within 2 mins of the test I get a hardware failure message. I've discovered that the test fails on the FPU stress test i'm kind of stuck on how to fix the issue
RYZEN 5 1400 (OC 3.7ghz)
ASUS B350I MOTHERBOARD
CORSAIR DOMINATOR PLATINUM 16GB 3000MHZ
EVGA 1080TI FTW3
Hi, I've met a issue with the FPU stress test, the system would crash instantly when I click the "Start" buttom
it was ok to run a solo CPU stress test over 2 hour, but I just dont understand why it went wrong when conducting the FPU test. Any Ideas?
I've attached a AIDA64 report of my mobo
CPU:7940x (1.15volt, OC 4.5ghz)
RAM:Gskill 8G*4 4266mhz c17 (I set the frequency at 2133)
I recently built my new rig and I am running some stress tests on my system to ensure stability. Everything works fine when using Asus' ROG RealBench software but when I use AIDA64 I start running into issues. The first time I ran AIDA64 I ran the stress test with stock preferences and settings for the trial version and the CPU, FPU, Cache, Memory, and GPU boxes checked. The test ran for 4 1/2 hours before a hardware failure was detected. I then tried running the test again and this time it only lasted 20 minutes. I then unchecked the 'Stress GPU' box and tried again, and it only lasted about 20 minutes again. I am now running the test without the 'Stress Memory' box checked as well now (leaving only CPU, FPU, and Cache left checked) and it's been 2 hours with no faults yet.
My guess is that it has something to do with my RAM, but I have no idea as to why or how. And if it is my RAM causing issues, is it a fatal error or will I be ok and I should just move on? Is there anything I can do to fix this? I am including some screen shots of my system specs and numbers.
On the picture with the red circle around my RAM speed, just ignore that, my memory is actually running at 3000 (I am using G. Skill Ripjaws V DDR4-3000 RAM) as you can see in the CPU-Z pics. On the screenshot of my BIOS settings, on the line for my DRAM Frequency, that has also been changed to Auto instead of [DDR4-3000 30x10...]
Let me know if I need to provide any more info. I do not really know how to use AIDA64 so this is new to me.
UPDATE: The stress test on the CPU, FPU, and Cache has been running for 11 hours now. I am now fairly certain that my hardware failure had to do with my memory during it's stress test. Will this cause a problem later on or should I just leave it alone?
UPDATE 2: Sadly the stress test failed at 11 hours 28 minutes. I'm not really sure what I should try next. Screenshots of failed test is now also attached. Any tips on what I can do to make this more stable would be much appreciated.
I'm just wondring if someone can explain to me a little bit about the FPU test in AIDA64. Until now I've been running stress tests with CPU, FPU, and cache being tortured. As I understand it this is fine, but running an FPU only SST will applying the peak temperature to a CPU in order to show that it's capable of running under such circumstances without throttling back.
I've so far got a stable 4.2Ghz clock out of my 4770K and I'm going to move on (with a target of 4.4GhZ or 4.3Ghz). At my 4.2Ghz clock the machine was stable for over 14 hours under AIDA64's CPU/FPU/Cache test and hit a peak temp of 75Â°c (on air). It generally floated around 65Â°c-70Â° on all cores.
Following this I've just carried out an FPU only test under the same spec. It peaked at 90Â°c on core 3, with the lowest peak on any other core being 81Â°c. It didn't throttle (I believe the Haswell chips do this at about 95Â°c, TJMax is 100Â°c), but I stopped it after 15 minutes.
Now obviously the intention of a stress test is to put the machine under more or at least as much continuous pressure as real world use would. Although my CPU didn't throttle, those FPU test temps are a bit higher than I'm really comfortable with. I think I read somewhere that the FPU test uses AVX instructions, but I'm not sure if that's correct - truth is I don't know how it works to reach it's temperatures. But what I really want to know is how representative of real-world use is it? What sort of applications might push the CPU in the same way? Many? A certain set or applications in a particular professional field? Are the results of this test alone something I should concern myself with if I've so far considered the same clock to be stable and safe under the full SST for over 14 hours?
If it helps, I'm running Windows 7 x64 and will be using the PC for music production, meaning it's heaviest load in real-world use will likely be Ableton Live plus a good handful of VST instruments and effects (creating and processing sound in real time). Native Instruments VSTs will feature fairly heavily.
I have trouble running thr FPU stress test after I changed the OC parameters. It's still 4.5GHz on CPU and 1600MHz on the RAM. Difference is that I do it with XMT and have turned Vcore and VTT to auto.