Jump to content
AIDA64 Discussion Forum
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By VTOLfreak
      Hi guys, I put together a system with ECC memory but AIDA64 is showing ECC as supported but disabled.
       
      CPU: Xeon E3-1275V5
      Motherboard: ASRock E3V5 WS (latest BIOS: 1.40)
      Memory: Crucial CT2K16G4WFD824A 2x16GB DDR4-2400 ECC UDIMM
       
      I have a CPU that supports ECC, ECC memory and a motherboard with a chipset that claims ECC support but doesn't mention ECC anywhere in the BIOS. So, is AIDA64 wrong and is ECC actually turned on? Or did ASrock screw up in the BIOS somewhere? Any other ways to check if ECC is enabled? I disabled the BIOS startup screen to watch it bootup but that didn't give any info on the memory detected. I attached the hardware report from AIDA64 if you guys want to take a look.
      Report.htm
    • By Consumer
      Hello,
      My system:
      Motherboard: Gigabyte GA-MA770T-UD3P (revision 1.1)
      CPU: Phenom II X4 925, RB-C2 stepping
      Memory: Kingston KVR1333D3E9SK4/16G (kit of four unbuffered ECC DDR3-1333 modules, 16 GB total, dual rank modules, each module has eighteen 256M x 8-bit FBGA)
      I manually underclocked the memory to 1066 MHz in BIOS. I left the timings as SPD auto-detected values for the 1066 MHz profile.
      Other values I set in the BIOS:
      DCTs Mode: Ganged
      DRAM ECC enable: Enabled
      DRAM MCE enable: Enabled
      Chip-Kill mode enable: Enabled
      DRAM ECC Redirection: Enabled
      DRAM background scrubber: 163.8us
      L2 cache background scrubb: 1.31ms
      DCache background scrubber: 5.24ms
      ...
      ...
      Bank Interleaving: Enabled
      Channel Interleave: Enabled
      Side-note: BIOS has no option for L3 cache background scrubbing.
      AIDA64 Extrene Edition 2.70.2200 prints:
      [ Memory Controller ]
      Memory Controller Properties:
      Error Detection Method: 64-bit ECC
      Error Correction: None
      Supported Memory Interleave: 1-Way
      Current Memory Interleave: 1-Way
      Supported Memory Speeds: 70ns, 60ns
      Supported Memory Types: SPM, EDO
      Supported Memory Voltages: 3.3V
      Maximum Memory Module Size: 1024 MB
      Memory Slots: 4
      ...and somewhere under [ North Bridge: AMD K10 IMC ], it prints...
      Error Correction:
      ECC: Supported, Enabled
      ChipKill ECC: Supported, Enabled
      RAID: Not Supported
      DRAM Scrub Rate: 163.8 us
      L1 Data Cache Scrub Rate: 5.24 ms
      L2 Cache Scrub Rate: 1.31 ms
      L3 Cache Scrub Rate: Disabled
      Because the North Bridge report section says "ECC Supported: Enabled" but the Memory Controller report section prints "Error Correction: None", I am confused. Are my modules running in ECC mode?
      Another side-note...I underclocked to 1066 MHz because: with stock 1333 MHz (A) it will take several minutes just to POST in "Ganged Mode" if "Channel Interleave" is enabled and "Bank Interleaving" is disabled, and ( B ) my board won't POST in "Ganged Mode" if both "Bank Interleaving" and "Channel Interleave" is enabled. It POSTs fine at stock 1333 MHz in "Unganged Mode" with both "Bank Interleaving" and "Channel Interleave" enabled, but in that Unganged case, AIDA64 will print "ChipKill ECC: Supported, Disabled", regardless of whether I enable Chip-Kill in the BIOS.
      Thanks,
      Consumer
×
×
  • Create New...