I don't see the pump speed etc. for the AIO. Is this a bug or does it need to be added ?
 
Blah again this should be in bugs section. 

So I'm about at my wits end with this, this is such a bizarre issue. I've already submitted a ticket to Asus about this and they are "researching" why this is happening for the last 2 days but I've heard nothing back yet, so I figured I'd do the same for AIDA64 and see if there are any answers/suggestions/solutions or jokes to ease my insanity.

AIDA64 Extreme ver. 6.10.5200 is the only hardware monitoring application I'm using as I've read multiple monitoring apps can cause the ITE IT8665E Super IO chip to bug out. (Among 1000 other things, is this thing just garbage or what?)
I'm also using the Logitech LCD configuration in AIDA64 to display temperatures/clockspeeds/VRM current/power/etc. basically all the important information I can fit spread between 4 pages on my Logitech LCD. However, I'm not monitoring fan speeds on my LCD just in case that's causing an issue.
After anywhere from 15 minutes to 2 hours, the fans I have connected to motherboard headers will stop spinning. After doing some experimentation and attempting to control the fans after they have stopped, I've figured out that the fan logic is randomly inverting. That is, 100% fan speed becomes 0%, and 0% becomes 100%, 66% fan speed becomes 34% fan speed etc. So after it happens, I can set the fans to 0% and they will spin back up to 100%, or to 34% and they will spin back up to 66%. So I have some form of solution, albeit not an ideal one.

I've also noticed that once the logic reverse happens, the fan sensor values in AIDA64 either freeze at their reported value, or they just show 0 RPM depending on how it's feeling at that particular instance. If I'm not running AIDA64 this will not happen, but it's an inevitability whenever AIDA64 is running. Rebooting the PC or sleep/resume will correct the issue for another 15 minutes to 2 hours.

Here are the only options I have enabled in the stability section of AIDA64:
Load Kernel driver Low-Level MSR Low-Level PCI Low-Level SMBus Low-Level sensor Low-Level SMART SMBus access through ACPI GPU Sensor Support I have disabled Asus WMI sensor support because I read that can solve the issue, but it hasn't helped.

This is also the second fresh install of Windows 10 on this machine, and it has happened during both installs. I'm on the latest 5220 BIOS, and changing all of the parameters of Q-Fan in the BIOS doesn't seem to have any effect.

Specs:
MB: Asus Prime X470-Pro CPU: AMD Ryzen 5 3600X RAM: 16GB G.Skill Ripjaws V 3600MHz GPU: AMD Radeon RX 5700 XT SSD's: Samsung 860 EVO 256GB + Samsung 840 Pro 128GB HDD's: Seagate Barracuda 2TB + Western Digital Blue 1TB PSU: Enermax Triathlor Eco 1000W  

Hi
A few odd things. I've recently added cheap water cooling to my PC.
It might be a misunderstanding  (or reconfiguration) on my pat. 
1) Sometimes when I start the PC and AIDA64  auto starts, it only shows the 3 white fan options as shown in the bottom of pic "Turn on PC".
If I close AIDA64 and restart it, or reboot, it comes up with the 5 fans it should have (see bottom of pic "Restarted"), 
2) very occasionally it starts correctly by showing the 5 fan options, but will say both the GPU Rad fan and the Temp Side Fan are 0 RPM even though they are spinning (sorry haven't got a pic for this)
Note, Power supply fan should be 0 RPM as it's a quite PS that only starts the fan if needed
3) With my CPU watercooler, I installed Corsairs iCUE fan control software (I presume this is needed to control the fans?).  That software shows completely different CPU temps to yours. When running your Stress Test, (all in C)
After 40 seconds, yours says 39 , iCUE says 33.7
After 2 mins, yours says 40  iCUE says 34.3
After 3 mins yours says 40  iCUE says 34.8
After 4 mins yours says 41, iCUE says 35.1
After 6 mins yours says 41, iQUE says 35.6
After 11 mins yours says 42 iQUE says 36.1
Pics of the above attached.  I left it running for a while longer, but the temp stayed fluctuating  between  41/42.
Then after I'd stopped your stress test for a couple of mins or so your s/w says 29, iQUE says 34.6
 
Turned on PC

 
 
Restarted PC

 
 
AIDA64 CPU Stress test after 40 secs

 
 
 
AIDA64 CPU Stress test after 2 mins

 
 
 
AIDA64 CPU Stress test after 3 mins

 
 
 
AIDA64 CPU Stress test after 4 mins

 
 
 
AIDA64 CPU Stress test after 6 mins

 
 
 
 
AIDA64 CPU Stress test after 11 mins

 
 
 
Stress test stopped for a couple of mins or so

 
 
System Spec:
Asus Vulcan Pro ROG Headset
Corsair Neutron GTX SSD 240GB (C drive, System)
Samsung 500GB EVO SSD  (D drive, Games)
SanDisk SSD Plus 480GB (E drive, Steam Library) 
Samsung 500GB EVO SSD  (F drive , Music S/W)
Samsung 500GB EVO SSD  (G, H, I drive,  Docs, More Programs, Email)
Toshiba HDwe140 4TB  (External enclosure, only plugged in to do backups) 

XFX RADEON RX480 Black Edition OC
Utech MMO Gaming Mouse 
Logitech G510 Keyboard
Razer Orbweaver Chrome
Focusrite Saffire Pro 24 Audio interface
Dell U2713HM monitor running at 2560 x 1440
BenQ GW2470 runing at 1920 x 1080
Intel Core i7 3820 a2011  3600 MHz
Asus P9X79 Socket 2011 ATX Motherboard
32GB Corsair Vengance DDR3 RAM
Win 10 Pro

Corsair 750 Watt HX750i Fully Modular ATX PSU/Power Supply
Corsair Hydro H55 on GPU
Corsair Hydro H100 v2 on CPU
NTZX H440 Mid ATX PC case
 

Hello,
I've moved this to a separate thread.
Ive rolled back to 4900 and the sensor page is now blank, the process is stuck detecting and end task process does not work as I get "access denied" this is persistent in removal and re-install of AIDA 64 ex

can you tell me if all check boxes ticked in the stability page for the following, which one 
ASUS WMI
ACPI ACCESS
ASUS ROG

Thanks again for the help

Hi,
All of the system fans are no longer appearing in the sensor page Using AIDA64 extreme 5.99.4944 Beta
RAD 1 header
RAD 2 Header
Chassis fan
I cannot remember when it happend,  just noticed another post and I checked mine. same problem