I have the latest BETA version for AIDA64 and the only sensor I am seeing from the AIO is the pump fan from the motherboard since it has a connector from the pump to the motherboard CPU fan header and it shows up as the CPU fan in AIDA64. The rest of the six fans connected to the iCUE controller core are not detected by AIDA64 and I have all the Corsair options other than Corsair Link sensor support checked in the stability section of the preferences. Attached is the USB dump you guys normally ask for in the other posts I have seen. Could use some help figuring this out to get my AIO fans detected in AIDA64 as I have a BeadaPanel to display statistics and fan speeds and would like to monitor these fans. Thanks for any help you can provide.
I saw a lot of thread about corsair water cooler but i have not see any with the new corsair h100i elite capellix. Corsair changed the way the cooler is connected to the board with this cooler. the pump and the fan now connect in a Commander CORE RGB & PWM Fan Controller(downgraded version of the commander pro with 6fan + 1 temps sensor) which is connected to the usb header. I can see the commander core in my usb device list in aida64 but i cant get the fan speed or the pump speed or water temps to show in the monitoring list. i already try downloading the new beta version that have the corsair hydro platinum support but it did not help. i join the corsair link dump file and the usb dump in case it can help. i also try to turn off icue and restart aida64 but aida didn't detected the commander core at all.
i dont understand what i am doing wrong.
the computer is a 3900xt on a asus b550-i motherboard if this change anything
As the title says really, I have a 5" pi screen that I use for the aida sensor panel. Every now and then the program just freezes, and all the sensors on my sensor paneI stop at the last readings reported. then when I try to start aida up again, it may or may not load, the only thing that gets it working is a restart. I've tried loads of things in these forums, and other recommendations on other site's, but still no joy.
I could really use some help with this.
My specs are
Rog x470-f gaming, ryzen 3900x, corsair h150i aio, 32gb corsair rgb ram 3200mhz, aorus 2070 super, Samsung 970 500gb m.2, Kingston 1tb ssd, corsair rm750x psu. 7 corsair ll120 fans linked to a commander Pro and lighting node.
I run icue for all my corsair stuff and aorus engine for the gpu. Also rgb fusion for the mobo and wallpaper engine.
Everything is up to date, and tonight I reinstalled aida, imported my sensor panel, but again it froze within a minute.
Is there any way to selectively disable fan speed monitoring in AIDA64?
I've been using it for my SensorPanel, but it conflicts with my ThermalTake Fan Control software. Both TT RGB Plus and the open-source replacement have this issue.
I can disable fan monitoring by unticking "low-level sensors" in the Stability menu, but this causes a ton of other things to be not monitored as well. All I want to do is disable fan-speed monitoring or even just ThermalTake fan speed.
Or is there a way to set up AIDA64 so that it won't conflict with my ThermalTake fans?
A few odd things. I've recently added cheap water cooling to my PC.
It might be a misunderstanding (or reconfiguration) on my pat.
1) Sometimes when I start the PC and AIDA64 auto starts, it only shows the 3 white fan options as shown in the bottom of pic "Turn on PC".
If I close AIDA64 and restart it, or reboot, it comes up with the 5 fans it should have (see bottom of pic "Restarted"),
2) very occasionally it starts correctly by showing the 5 fan options, but will say both the GPU Rad fan and the Temp Side Fan are 0 RPM even though they are spinning (sorry haven't got a pic for this)
Note, Power supply fan should be 0 RPM as it's a quite PS that only starts the fan if needed
3) With my CPU watercooler, I installed Corsairs iCUE fan control software (I presume this is needed to control the fans?). That software shows completely different CPU temps to yours. When running your Stress Test, (all in C)
After 40 seconds, yours says 39 , iCUE says 33.7
After 2 mins, yours says 40 iCUE says 34.3
After 3 mins yours says 40 iCUE says 34.8
After 4 mins yours says 41, iCUE says 35.1
After 6 mins yours says 41, iQUE says 35.6
After 11 mins yours says 42 iQUE says 36.1
Pics of the above attached. I left it running for a while longer, but the temp stayed fluctuating between 41/42.
Then after I'd stopped your stress test for a couple of mins or so your s/w says 29, iQUE says 34.6
Turned on PC
AIDA64 CPU Stress test after 40 secs
AIDA64 CPU Stress test after 2 mins
AIDA64 CPU Stress test after 3 mins
AIDA64 CPU Stress test after 4 mins
AIDA64 CPU Stress test after 6 mins
AIDA64 CPU Stress test after 11 mins
Stress test stopped for a couple of mins or so
Asus Vulcan Pro ROG Headset
Corsair Neutron GTX SSD 240GB (C drive, System)
Samsung 500GB EVO SSD (D drive, Games)
SanDisk SSD Plus 480GB (E drive, Steam Library)
Samsung 500GB EVO SSD (F drive , Music S/W)
Samsung 500GB EVO SSD (G, H, I drive, Docs, More Programs, Email)
Toshiba HDwe140 4TB (External enclosure, only plugged in to do backups)
XFX RADEON RX480 Black Edition OC
Utech MMO Gaming Mouse
Logitech G510 Keyboard
Razer Orbweaver Chrome
Focusrite Saffire Pro 24 Audio interface
Dell U2713HM monitor running at 2560 x 1440
BenQ GW2470 runing at 1920 x 1080
Intel Core i7 3820 a2011 3600 MHz
Asus P9X79 Socket 2011 ATX Motherboard
32GB Corsair Vengance DDR3 RAM
Win 10 Pro
Corsair 750 Watt HX750i Fully Modular ATX PSU/Power Supply
Corsair Hydro H55 on GPU
Corsair Hydro H100 v2 on CPU
NTZX H440 Mid ATX PC case