Jump to content
AIDA64 Discussion Forum
jcambros

EVGA 280mm CLC setup help

Recommended Posts

Hello,

I have an EVGA 280mm CLC in my computer. I want to monitor the fan speeds through AIDA64, but cannot figure out how to get the fans to show up for monitoring. Note that I do see the Pump Speed appear on the CPU Fan Speed in AIDA64 (reporting at half speed?)

I have plugged the CLC's 3-pin power connector into the CPU Fan Header on the motherboard (ASUS z390-i).

Both of the fans on the radiator have their 4-pin PWMs plugged into the CLC and the USB 2.0 connection from the CLC is plugged into the USB 2.0 connector on the motherboard.

I can see the AIO Pump Speed and Fan Speeds in the EVGA Flow Control App, but do not know how to have them appear in AIDA64.

Is there a setting I am missing somewhere?

Share this post


Link to post
Share on other sites

I'm kind of new at using this stuff myself but I have been digging around in the settings for about a month. (AKA - I have no idea what I'm doing) but if you open AIDA64 in the top left you can click on "File" then "Preferences"  This will open a new window. In the left side pane, I think its like the 4th one down you will see "Stability".  There is some stuff ya can turn on in there that might help. Wish I could be more of a help. Don't forget to search these forums too :P

Share this post


Link to post
Share on other sites
On ‎6‎/‎1‎/‎2019 at 7:58 PM, jcambros said:

Hello,

I have an EVGA 280mm CLC in my computer. I want to monitor the fan speeds through AIDA64, but cannot figure out how to get the fans to show up for monitoring. Note that I do see the Pump Speed appear on the CPU Fan Speed in AIDA64 (reporting at half speed?)

I have plugged the CLC's 3-pin power connector into the CPU Fan Header on the motherboard (ASUS z390-i).

Both of the fans on the radiator have their 4-pin PWMs plugged into the CLC and the USB 2.0 connection from the CLC is plugged into the USB 2.0 connector on the motherboard.

I can see the AIO Pump Speed and Fan Speeds in the EVGA Flow Control App, but do not know how to have them appear in AIDA64.

Is there a setting I am missing somewhere?

You need to enable Corsair Link sensor support in AIDA64 / main menu / File / Preferences / Stability to enable CLC support.

Share this post


Link to post
Share on other sites

I'm having this same issue. I have an EVGA 240mm CLC and I've enabled both Corsair Link sensor support and Asetek LC sensor support as I believe was recommended elsewhere. Under Computer Summary, I see the USB device CCIV which I believe is associated with the CLC.

Even with these settings, I've been unable to locate sensor data in AIDA64 for the CLC fans while this data does appear in the EVGA Flow Control application.

Running AIDA64 Extreme version 6.00.5100 and EVGA Flow Control version 2.0.7

aidaPrefs.JPG

aidaSensor.JPG

evgaSensor.JPG

Share this post


Link to post
Share on other sites
On ‎7‎/‎17‎/‎2019 at 10:14 PM, fache said:

I'm having this same issue. I have an EVGA 240mm CLC and I've enabled both Corsair Link sensor support and Asetek LC sensor support as I believe was recommended elsewhere. Under Computer Summary, I see the USB device CCIV which I believe is associated with the CLC.

Even with these settings, I've been unable to locate sensor data in AIDA64 for the CLC fans while this data does appear in the EVGA Flow Control application.

Running AIDA64 Extreme version 6.00.5100 and EVGA Flow Control version 2.0.7

Please right-click on the bottom status bar of AIDA64 main window --> System Debug --> USB Dump. Copy-paste the full results into this topic, or attach the results as a TXT file to your post. You may need to enable status bar in AIDA64 / main menu / View first.

Also right-click on the bottom status bar of AIDA64 main window --> Sensor Debug --> Corsair Link Dump. Copy-paste the full results into this topic, or attach the results as a TXT file to your post.


Thanks,
Fiery

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...