Jump to content
AIDA64 Discussion Forum
Ventilator

Rotate output in AIDA64 LCD config for Logitech Arx app

Recommended Posts

On ‎8‎/‎12‎/‎2019 at 12:38 AM, Ventilator said:

Would be nice if you could rotate output 90 degrees in AIDA 64 LCD config for Logitech ARX.

This, so you can get tablet mode.

 

There's no need to rotate anything in AIDA64.  Just rotate your tablet to landscape mode, enable Logitech Arx LCD in AIDA64, check the recommended resolution on your tablet on the blue AIDA64 splash screen.  De-activate Logitech Arx LCD, enter the right resolution in the Preview resolution field (AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / Logitech Arx), enable Logitech Arx LCD again, and you should be good to go.

Share this post


Link to post
Share on other sites

Thank you for the reply. I have manually set the resolution as it were required for it to work, but it only uses around 1/3 of the tablet screen where the rest of right side is all white.
This could be because you can only set it up in portrait mode in AIDA, and is why were thinking of rotating the text to maybe fill whole screen. :)

I used to use a Logitech G19, but the keyboard broke after many years and then found out about the Aida+Logitech which is a great thing and have around 4 times the screen space vs G19 to add even more info. :)

Share this post


Link to post
Share on other sites
32 minutes ago, Ventilator said:

Thank you for the reply. I have manually set the resolution as it were required for it to work, but it only uses around 1/3 of the tablet screen where the rest of right side is all white.
This could be because you can only set it up in portrait mode in AIDA, and is why were thinking of rotating the text to maybe fill whole screen. :)

I used to use a Logitech G19, but the keyboard broke after many years and then found out about the Aida+Logitech which is a great thing and have around 4 times the screen space vs G19 to add even more info. :)

What kind of tablet do you have?  We've tested this with our Nexus 9 tablet, which reflects that a previous resolution of 1024 x 671 should be used in landscape mode.  When we set it to that resolution, the LCD preview is in landscape mode (as it should be), and whatever we put on the LCD layout gets displayed properly on the screen.  Almost the whole screen is filled, with only the top Android notification bar and the bottom Android virtual buttons bar make the usable area of the 9-inch screen a bit smaller.

  • Like 1

Share this post


Link to post
Share on other sites
18 hours ago, Fiery said:

What kind of tablet do you have?  We've tested this with our Nexus 9 tablet, which reflects that a previous resolution of 1024 x 671 should be used in landscape mode.  When we set it to that resolution, the LCD preview is in landscape mode (as it should be), and whatever we put on the LCD layout gets displayed properly on the screen.  Almost the whole screen is filled, with only the top Android notification bar and the bottom Android virtual buttons bar make the usable area of the 9-inch screen a bit smaller.

This seem to work now. I have a "Lenovo Tab 4 Plus 10.1"

Thank you very much for the help, and have a nice day.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Similar Content

    • By beada
      BeadaFrame Display Kit is an ARM Cortex-A7 development platform which bundled with a 7" TFT LCD Display. It can be powered and communicated with PC Host by a single Micro USB cable. Currently we use it as a secondary PC monitor for display of hardware status through Remote Sensor LCD.
      The question is --  is there any way to implement it as a native support of AIDA LCD screen? We are running Debian Stretch on the ARM Cortex-A7 core.


       
      And more details of this display kit:
      CPU
      NXP/Freescale ARM Cortex-A7 i.MX6ULL
      RAM
      512MB DDR3L
      Storage
      16GB/32GB eMMC
      Connectivities
      1 x WIFI 802.11 b/g/n module(AP6212) 1 x USB 2.0 Host(Type A) 1 x USB 2.0 OTG(Micro-USB) Display
      7.0" TFT LCD: 800x480 (AT070TN92) , w/ touch and bezel
      On Board Resources
      Reset Circuit with reset button 1 x Power select jumper 1 x Boot select jumper 1 x USER LED Dimension
      188 x 118 x 35(mm)
      Operating System
      Debian Stretch
      Consumption
      5V/350mA
    • By Shaman
      Dear all,
      I am trying to figure out the best option for a small (max 7'') external screen to use with SensorPanel.
      I find lots of options on eBay that I suppose are all viable (e.g., https://www.ebay.co.uk/itm/7inch-HDMI-LCD-H-with-case-1024x600-IPS-Capacitive-Touch-Screen-Audio-Output/133067577890).
       
      What I am unsure at the moment:
      - Is the quality/resolution of the screen important?
      - Is touch input needed/used?
      - Is there any difference (limitations) between the three available options (using an HDMI connected screen, a USB connected one and/or an affordable Android tablet)? 
       
      Any input would be appreciated. Thank you in advance!
       
      Best,
      S
    • By Roy
      Hi,
      it would be nice if there was the possibility to send sensor values unformatted as a number or percentage, via a serial port.
      Similar to the LCD displays, only without formatting, or pure numbers with separators.
      Together with a small GUI.
      Background is the simple evaluation of the data with a microcontroller and display in different ways.
      I imagine not only LCD or OLED, but rather seven segment display, nixi tubes or an analog pointer display. That would create a lot of possibilities.
    • By Wampo
      Hey Aida Team,
      i have some issues with this Adafruit LCD wich is recomended. On the two Pictures you can see what aida should do and what can i see on the Display. The First line is completely erased and the screen is flickering. The Adafruit Backpack is set to 20x4 LCD. When the Display is updating you can see the right setting for a millisecond.
      But if i change the LCD Setting in AIDA to 16x2, and leave the Backpack in 20x4 mode,  the Screen isn flickering and the first line is there. I think you got a little problem with the 20x4 Driver. I have Searched for the code but i cant find it, to edit it if i found the failure. 
       
      Please give me response for this BUG. I have extra ordert this overpriced 50€ LCD for it. 
      Greetings Daniel from Germany


      VID_20181129_160917.mp4
    • By Fiery
      We've added support for RoboPeak RPUSBDisp color graphical USB-connected LCD display.

      You can enable the LCD device from AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / RoboPeak. Currently there is no Windows driver made specifically for RoboPeak displays.  But there's a workaround: you can use the AlphaCool LCD driver (Version 2.1).  The driver installation has to be forced due to the USB device ID mismatch (between AlphaCool and RoboPeak displays).
      The driver installation works as:
      Open Device Manager --> Other devices --> double-click on rp-usbdisp --> Update Driver button --> Browse my computer for driver software --> Let me pick from a list of available drivers on my computer --> Show All Devices --> Next button --> Have Disk button --> Browse button --> select acusbdisplay.inf file from the AlphaCool LCD driver folder --> Next button --> press Yes button on the Update Driver Warning message box.

      You can order a RoboPeak display from DFRobot at:
      https://www.dfrobot.com/product-1062.html#.UqfXHfSnoqX
      You can find the new AIDA64 beta update at:
      https://www.aida64.com/downloads/latesta64xebeta
      Please let us know if you find any difficulties enabling or using this new feature. Also let us know if you've got another kind of LCD device that is currently unsupported by AIDA64.
      Regards,
      Fiery
×
×
  • Create New...