Share your Sensorpanels

[JariKoi]

Post removed by JariKoi

[Shephard]

somehow you are complicating everything, the range of one sensor can be set to anything and at the same time it will be divided by 16 (that is, from 0 to 15), if you need to expand the range, you install two identical sensors but with different range values at which each of the sensors will still be divided by 16, that is, if you need to show, for example, a frequency of 1000 MHz, you can make it with one sensor with 16 divisions or two sensors with 32 divisions, naturally, dividing 1000 by 32 is not very convenient, you will get fractional values, so There is a table that you gave as an example, which shows how it is most convenient to separate the ranges if you have more than one sensors..
  in the end, someone will probably have to make instructions for the distribution of these sensors, apparently a simple table is not enough for understanding..

[Mask Blue]

17 minutes ago, Shephard said:

somehow you are complicating everything, the range of one sensor can be set to anything and at the same time it will be divided by 16 (that is, from 0 to 15), if you need to expand the range, you install two identical sensors but with different range values at which each of the sensors will still be divided by 16, that is, if you need to show, for example, a frequency of 1000 MHz, you can make it with one sensor with 16 divisions or two sensors with 32 divisions, naturally, dividing 1000 by 32 is not very convenient, you will get fractional values, so There is a table that you gave as an example, which shows how it is most convenient to separate the ranges if you have more than one sensors..
  in the end, someone will probably have to make instructions for the distribution of these sensors, apparently a simple table is not enough for understanding..

I appreciate your help, but I'm not complicating anything, I just wish you understood what I'm trying to explain. If we use this table to create a sensor to measure the processor clock, this table won't function correctly. I've even used the same table and followed all the steps to create a clock sensor, but it doesn't work properly.

I just want to know what minimum and maximum values I should use in the sensor for it to work correctly, considering that the maximum and minimum values of the CPU are from 0 to 9000

[Graffix]

47 minutes ago, JariKoi said:

You can download them all here.

LEGEND.  Thanks!

[rinaldop]

24 minutes ago, Mask Blue said:

I appreciate your help, but I'm not complicating anything, I just wish you understood what I'm trying to explain. If we use this table to create a sensor to measure the processor clock, this table won't function correctly. I've even used the same table and followed all the steps to create a clock sensor, but it doesn't work properly.

I just want to know what minimum and maximum values I should use in the sensor for it to work correctly, considering that the maximum and minimum values of the CPU are from 0 to 9000

There is no reason to keep the range of the CPU at 0 to 9000, that is just what the developers of AIDA64 picked. You can set it to 1000-5000 that should cover the range of any CPU used in a home PC.

I you really want to cover from 0-9000 in steps of 1 MHz you are going to need 9001 steps.

Let us look at the table:

Instead of Sensor 8 in this table you need a make Sensor 8 like this:

Sensor 8 98-113

Then keep going

Sensor 9 112-127

Sensor 10 126-141

Keep going with the pattern until you get to 9000. That is a lot of work that is not needed. No CPU will go under 1000 or over 5000 in normal use. Just start the pattern at 1000 and end at 5000.  It should take about 250 sensors to cover that range. I do not think anyone needs a gauge that displays CPU clock frequency with 1 MHz precision but if that is what you want then this is what you must do.

 

[rinaldop]

1 hour ago, Shephard said:

somehow you are complicating everything, the range of one sensor can be set to anything and at the same time it will be divided by 16 (that is, from 0 to 15), if you need to expand the range, you install two identical sensors but with different range values at which each of the sensors will still be divided by 16, that is, if you need to show, for example, a frequency of 1000 MHz, you can make it with one sensor with 16 divisions or two sensors with 32 divisions, naturally, dividing 1000 by 32 is not very convenient, you will get fractional values, so There is a table that you gave as an example, which shows how it is most convenient to separate the ranges if you have more than one sensors..
  in the end, someone will probably have to make instructions for the distribution of these sensors, apparently a simple table is not enough for understanding..

If you go for a frequency range of 0-1000 with 1 sensor each image will count for a range of 66.67 (1000 divided by 15). If you do a range of 0-1000 with 2 sensors each image will count for a range of 33.33 (1000 divided by 30) If you want a range of 0-1000 with each image covering a range of 1 you would need 1000 images (0 to 999) since 1000 divided by 1000 is 1. The table works for 0-100 since there are 100 images (image 0-99) spread over 8 sensors.

Just like 100 images (0-99) need 8 sensors to go from 0-100, 1000 images (0-999) would need about 67 or 68  sensors.

[rinaldop]

6 minutes ago, Halfcutt said:

Must be a golden sample. You are a millionaire. You could retire selling that one CPU.

The highest you would need to set for any consumer level CPU is 6000mhz. You would need such a crazy amount of gauges to do that. Not sure if Aida64 could even process that many gauges at once. The file size would be insane.

Or am I missing something?

No, you are correct.

[1 PC Tip a day]

In my opinion, "100 state" gauges are only worth it when you want to represent values that virtually can go from 0 to 100. For example, temperature, % usage and son on. Trying to represent 1 MHz with a single .png file should crash Aida64.

[Shephard]

In my opinion, showing the frequency of the processor in the form of GAUGE does not make sense at all, since in almost all processors the frequencies change at such a speed that even the eye does not determine that it would also show the program, the processor loads should be set up to 100%, and It is enough to show the frequency in the form of numbers.

[rinaldop]

20 minutes ago, 1 PC Tip a day said:

In my opinion, "100 state" gauges are only worth it when you want to represent values that virtually can go from 0 to 100. For example, temperature, % usage and son on. Trying to represent 1 MHz with a single .png file should crash Aida64.

Actually temperature can go above 100. The only sensors that will not go over 100 are the utilization sensors, the ones that display percentage.

[Shephard]

I even expose the temperatures 20-80, but I have water, it just will not be below 20, by the fact that the room temperature, and if above 80, it already starts to boil and the pressure valve should be opened.

[1 PC Tip a day]

1 hour ago, rinaldop said:

Actually temperature can go above 100. The only sensors that will not go over 100 are the utilization sensors, the ones that display percentage.

 

1 hour ago, Shephard said:

I even expose the temperatures 20-80, but I have water, it just will not be below 20, by the fact that the room temperature, and if above 80, it already starts to boil and the pressure valve should be opened.

Yep, that's what I meant with "virtually". My CPU or GPU don't go below 25 ºC and above 85 ºC, but I made a 100 state gauge for a range of 0-100.

[Shephard]

1 hour ago, 1 PC Tip a day said:

 

Yep, that's what I meant with "virtually". My CPU or GPU don't go below 25 ºC and above 85 ºC, but I made a 100 state gauge for a range of 0-100.

I put 80 degrees the maximum, because it is more convenient to watch the red indication on the panel, but who does not make sense on air cooling, because they do not need to monitor the pressure of water ..

[poke_]

On 11/5/2023 at 2:28 PM, poke_ said:

Hu Tao (Genshin Impact) themed Sensor Panel, 480x1920 (Aspect Ratio 1:4)
Gauges go from Red -> Green -> Cyan when full

Not good at graphic design, I think the frames turned out pretty neat though

Used Paint.NET for everything, I attached the .pdn file as well for the background image, in case anybody wants it

HuTao-480x1920.sensorpanel 1.45 MB · 3 downloads Hu Tao 480 - 1920.pdn 647.28 kB · 2 downloads

Forgot to change the clock's font to Genshin's font.
Also changed around the placement of the drive info and time + added date:

Hu Tao 480 - 1920.pdn HuTao-480x1920_v2.sensorpanel

[ashf]

On 10/31/2023 at 6:57 PM, Olaf Kroll said:

I Love this Skin!

 

any chancei can get a link for this one?

[Arbit]

On 11/3/2023 at 1:10 AM, Jonathan Williams said:

Best I've ever seen, I would pay for that.

I love that as well. I'm using a vertical panel. Here is my modification. If you search my name, you can find this panel. For download. 

[Surjeet]

13 hours ago, ashf said:

any chancei can get a link for this one?

Is this the one you are looking for: Size 1024 x 600

https://forums.aida64.com/topic/667-share-your-sensorpanel/?do=findComment&comment=54083

 

[E P]

Curious if anyone has made a panel and used it with a transparent side panel.  I modified several of my PCs this way and display various graphics but an instrument panel would be a nice change.   I know it would just be dimension adjustments but curious about design that would stand out best.   My interior is mostly white.   Would love to see examples if someone is using it this way.    Thanks.

[Shephard]

I haven’t examined OLED displays yet, but judging by the technology, these matrices should be quite transparent and not require backlighting if you remove the rear diffuser.. but I could be wrong, due to the fact that I haven’t had the opportunity to work with such displays yet.. just do not confuse QLED these are different principles

[rinaldop]

2 hours ago, Halfcutt said:

I agree with everything you have said in the quoted post and your other posts. But you are wrong to say that no CPU will go under 1000mhz. Most any modern Intel CPU will. At an idle state. As a mater of fact, my i9-10850K drops to 800mhz as I type this.

I never paid attention to my CPU clocks when I had Intel CPUs. I am using an AMD 7800X3D now. I found this interesting comment on the internet:

Quote

 

I noticed in idle (1% utilization and no processes using much - this is a fresh install)  the CPU is at 3.0 - 3.7 GHz. My old i7-7700k idled at under 1 GHz. So I wonder if there is a setting I can change? 

 

This is typical of Ryzen CPU's. They have a "race to sleep" strategy that keeps the clock speeds high when progrrams like HWmonitor poll the clock speed.

In reality the CPU is extensively using sleep states to conserve power.

 

   

[Shephard]

in reality, modern processors are able to reduce frequencies much lower, it just happens at such a speed that no sensors or programs can monitor this, and don’t forget that the operating system also consumes something, and from this frequency constantly float, in fact, as I already said, there is no need to set the Gauge to the processor frequency; to effectively understand its operation, it is enough to set the processor load, and simply leave the frequency as a frequency number.. the panel is not an oscilloscope and not an accurate instrument for measuring vibrations the earth's crust, this is just a way to visualize processes..

[E P]

5 hours ago, Halfcutt said:

 

I believe you are referring to Snowblind. Separate the layers of a LCD screen and apply it to a glass panel? Yes, the interior of PC has to be as 'white' as possible to get a good effect. It would never be as vibrant as the original screen was though.

I would love to see what you can do.

I think if done right, a sensor panel would look cool.

I think you misunderstood or my explanation wasn't clear enough (pun intended).  I have already modified my PCs with the transparent side panel myself (similar to snowblind).  I am curious if anyone has created sensor panels that work well with the high contrast needed rather than colorful panels seen in most shared examples that are displayed on smaller sized color panels (which I have done with one PC as well).

Thanks.

[ninjawhattt636]

On 7/7/2023 at 7:06 PM, crackerman said:

 

i would love to use this panel!

[Shephard]

16 hours ago, E P said:

I think you misunderstood or my explanation wasn't clear enough (pun intended).  I have already modified my PCs with the transparent side panel myself (similar to snowblind).  I am curious if anyone has created sensor panels that work well with the high contrast needed rather than colorful panels seen in most shared examples that are displayed on smaller sized color panels (which I have done with one PC as well).

Thanks.

 

20 hours ago, Shephard said:

I haven’t examined OLED displays yet, but judging by the technology, these matrices should be quite transparent and not require backlighting if you remove the rear diffuser.. but I could be wrong, due to the fact that I haven’t had the opportunity to work with such displays yet.. just do not confuse QLED these are different principles

you want Aida64 to display brighter colors, I understand you, that is, that the color palette should have more saturated shades, if so, then I already wrote, you should wait a little and you will have the opportunity to use ready-made solutions..

[Kouichi144]

GPUの設定が突然消えました。
これはRX6600XTです。誰かが私に解決策を教えてください。