Jump to content

Fiery

Administrators
  • Posts

    12278
  • Joined

  • Last visited

  • Days Won

    541

Everything posted by Fiery

  1. I'm not sure. I'd have to see the dumps I've requested above. I've sent you an email about this issue
  2. Thank you for the screenshots. The issue will be fixed in the next AIDA64 beta update due in a few days from now. I'll post a message into this topic once the new beta is available for download.
  3. Thank you for the dumps. The issue will be fixed in the next AIDA64 beta update due in a few days from now. I'll post a message into this topic once the new beta is available for download.
  4. Thank you for the dumps. The issue will be fixed in the next AIDA64 beta update due in a few days from now. I'll post a message into this topic once the new beta is available for download.
  5. Thank you! The Vcore register of the sensor chip seems to be fixed, no matter what Vcore you use. I'm afraid we need more dumps from you to further investigate this issue -- I hope you don't mind Please do the following: 1) Select a Vcore setting, note down the value that you've selected in the BIOS Setup. Also note down the Vcore reading that E-LEET shows. Then create a new ISA Sensor Dump and SMBus Dump (Full) dump. 2) Then select a different Vcore setting, note down the value that you've selected in the BIOS Setup. Also note down the Vcore reading that E-LEET shows. Then create a new ISA Sensor Dump and SMBus Dump (Full) dump. Please compress those 4 dumps and attach the ZIP file to your post. If you prefer to send the files in email instead, please send me a private message. Thank you in advance!
  6. That's because AIDA64 reads EC registers directly, using classic ISA port I/O. You can ignore the warning messages.
  7. Thank you. That's quite puzzling. Maybe we're using a different multiplier for Vcore calculation than what we should? Can you please create a screen shot with AIDA64 Sensor Page + E-LEET Monitoring page at a different Vcore setting in the BIOS Setup?
  8. Thank you. Please check if CPU VID, as reported by AIDA64 on the Computer / Overclock page matches CPU Vcore as measured by E-LEET. If it does, then we'll replace the Vcore reading by the CPU VID value.
  9. It refers to a very old thing, dating back to Win95: http://i1.blogs.msdn.com/b/oldnewthing/archive/2007/03/12/1861385.aspx
  10. Do you mean all the other software can read the voltage, or they can not? BTW, this is due to a fundamental change in the voltage management of Pascal. We're already looking into it, but there's no fix available yet
  11. There's a chance E-LEET reports CPU VID voltage as Vcore. Can you please check if CPU VID, as reported by AIDA64, matches the Vcore reading in E-LEET? What I meant is: start AIDA64, go to its Computer / Sensor page, move AIDA64 window to the left side (left half) of the Windows Desktop. Then open E-LEET, go to its Monitoring page, move E-LEET window to the right side of the Windows Desktop, and then make a screen shot that would show all sensor readings both software in the same time, on a single shot.
  12. Thank you for the feedback
  13. Please try it again. There was a silly limitation in the forum settings that we've now fixed As long as it's enabled in the Stability settings, and the driver is properly installed, AIDA64 should be able to read the sensor values from your water cooler device.
  14. Thank you! Please upgrade to the latest beta version of AIDA64 Extreme available at: http://www.aida64.com/downloads/latesta64xebeta After upgrading to this new version, make sure to restart Windows to finalize the upgrade. Let me know how it works.
  15. Vcore in the BIOS Setup tends to be higher than under Windows, since in the BIOS Setup the CPU cannot go to low-power state by executing idle cycles. Make sure to compare Vcore readings in AIDA64 against E-LEET. As for the other readings, only those readings are available on your motherboard that you can see on the Monitoring page of E-LEET. If you miss some readings, then please create a screen shot that shows AIDA64 Sensor page and the Monitoring page of E-LEET side-by-side, so we can compare every reading against a reference list of readings.
  16. Running the latest RST drivers, please create a new ATA Dump and SMART Dump, before and after sleep. As for the water pump issue, try to enable both Asetek LC sensor support and Corsair Link sensor support in AIDA64 / main menu / File / Preferences / Stability, and restart AIDA64.
  17. Only Asus can explain how those values work. We only read them out from the EC chip and report them as they are, as raw readings.
  18. Thank you for your feedback
  19. Thank you. We've implemented the requested readings in the latest AIDA64 beta update: http://www.aida64.com/downloads/latesta64xebeta Please let me know how it works
  20. The above mentioned new AIDA64 beta update is available at: http://www.aida64.com/downloads/latesta64xebeta Let me know how it works
  21. Please upgrade to the latest beta version of AIDA64 Extreme available at: http://www.aida64.com/downloads/latesta64xebeta After upgrading to this new version, make sure to restart Windows to finalize the upgrade. Let me know how it works
  22. We've tried it under Windows 10, and it shows disk activity with a polling resolution of 100 millisec, so it works as expected. What Windows version do you have installed?
  23. Do you have a smart PSU or a USB-connected sensor device like Aquaero or Corsair Link?
  24. You have to adjust the update frequency for the feature you're using. If you're using those disk related items on SensorPanel, then you need to adjust the update frequency for the SensorPanel. And no, we don't use the disk performance API incorrectly.
×
×
  • Create New...