Jump to content
AIDA64 Discussion Forum
Fiery

New LCD device support: Samsung SPF Digital Photo Frames

Recommended Posts

I said this in between:

 

mm it is gone again.

Is it possible to delay aida64 to make sure it does not load while the ramdisk is being loaded from the ssd at windows boot time ?

Note: When I exit aida64 and re open it, disk never shows anymore.

 

 

So it also fails with 10 GB (It was working once for a reason I do not know).

 

I had like 3 or 4 beta updates since then.

Is there a way to download the previous betas to test ?

 

 

I use the dataram ramdisk (paid version):

 

dataram.png

 

dataram_b.png

 

dataram_c.png

Share this post


Link to post
Share on other sites

We've checked, and it works fine for us, with a 1000 MB sized RAM disk. Hot-plugging it also works properly. If you need a previous beta, please let me know which ones are you interested in, and I'll send them to you.

Share this post


Link to post
Share on other sites

I need the previous version -2

What version is zero? :) Do you mean -2 from the latest stable update? Do you mean stable update or beta package? :)

Before your post we've had the following few releases:

Beta Update 3725

Beta Update 3720

Beta Update 3718

Beta Update 3716

Beta Update 3709

Beta Update 3703

Stable Update 3700

Of course we can go even further back, if you want.

Share this post


Link to post
Share on other sites

I jsut got a new beta update (still failing on the ramdisk).

So would be the first beta that was supporting the disk speed(I do not recall which one was it).

.

Share this post


Link to post
Share on other sites

I jsut got a new beta update (still failing on the ramdisk).

So would be the first beta that was supporting the disk speed(I do not recall which one was it).

.

You've got a private message ;)

Share this post


Link to post
Share on other sites

Thanks,

It is still not showing it, I guess it is an issue not related to aida64.

Yes, that's what I've meant when I've stressed the fact that we haven't touched the drive activity monitoring part of AIDA64 since the very first implementation ;)

Share this post


Link to post
Share on other sites

When I re-recreate a ram disk image it is ok and seen again, but after a reboot it is gone.

Looks like an issue with dataram or windows 10.

Share this post


Link to post
Share on other sites

Dear Aida64,

 

i recently picked up a SPF-83M which i converted into a SPF-83V via Firmware update.

In AIDA64 extreme edition it is recognised as SPF-83V, no matter which firmware i have on the DPF.

The problem is, it disconnects after a few seconds in AIDA64.

I have read that:

"- If the device disconnects after a few seconds, enable the option Send keep-alive packet in AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / Samsung"

 

Apparently there is no such option visible for me under this path.

Is it under a different path?

 

Also you wrote that SPF-83V is not supported.

Is it still so until this day?

Share this post


Link to post
Share on other sites

Also you wrote that SPF-83V is not supported.

Is it still so until this day?

It is still the case I'm afraid.

Share this post


Link to post
Share on other sites

i am using windows10 x64 and i want use SPF-72H to connect to my computer.But after i installed the LibUSB driver and open aida64 it still shows usb devices not found.i found my 72H has a strange device ID :  0851-1543 in mass storage mode.is there anybody knows what happened?

 

And when i install the driver,if i open the installer_x64.exe directly it only shows a window and close quickly,so i have to open my devices manager and install the driver manual,is that the problem?

 

 

PS:forgive my terrible english,it is not my first lauguage ;)

Share this post


Link to post
Share on other sites

i am using windows10 x64 and i want use SPF-72H to connect to my computer.But after i installed the LibUSB driver and open aida64 it still shows usb devices not found.i found my 72H has a strange device ID :  0851-1543 in mass storage mode.is there anybody knows what happened?

 

And when i install the driver,if i open the installer_x64.exe directly it only shows a window and close quickly,so i have to open my devices manager and install the driver manual,is that the problem?

 

 

PS:forgive my terrible english,it is not my first lauguage ;)

Sounds odd. Maybe your device is an old one that doesn't yet have a Samsung USB device ID. Yours seem to have a MXIC (Macronix) device ID. Can you switch it to mini-monitor mode? It would be very useful to see what the device ID is in mini-monitor mode.

Share this post


Link to post
Share on other sites

Sounds odd. Maybe your device is an old one that doesn't yet have a Samsung USB device ID. Yours seem to have a MXIC (Macronix) device ID. Can you switch it to mini-monitor mode? It would be very useful to see what the device ID is in mini-monitor mode.

I found a computer installed Windows xp then install SFM, but the software can't identify my SPF72H, is this product contains many different sub model?

post-34591-0-29431800-1456966206_thumb.jpg

 

and I found a disturbing phenomenon that my user manual has no information about mini - monitor :(

Share this post


Link to post
Share on other sites

I found a computer installed Windows xp then install SFM, but the software can't identify my SPF72H, is this product contains many different sub model?

attachicon.gifspf72h.jpg

 

and I found a disturbing phenomenon that my user manual has no information about mini - monitor :(

Many SPF models have sub-models and revisions, some of them have three variants :( I guess your SPF doesn't support mini-monitor yet, but only a second or third revision -- still named SPF-72H -- does.

Share this post


Link to post
Share on other sites

Many SPF models have sub-models and revisions, some of them have three variants :( I guess your SPF doesn't support mini-monitor yet, but only a second or third revision -- still named SPF-72H -- does.

that means i wasted 20 USD to buy the Second-hand good,opps. :blink:

Share this post


Link to post
Share on other sites
 
My work
 
Photo Frame SPF-72H
 
post-30668-0-63441500-1457882892_thumb.jpg post-30668-0-46651200-1457882893_thumb.jpg post-30668-0-17742100-1457882894_thumb.jpg
 
 

 

There are problems in the photo frame. After a while the image on the photo frame freezes and AIDA64 stops responding. It helps only restart photo frame. Compression set to a value of 50.

 

 

If remove all Samsung drivers then LibUsb driver does not see the photo frame.

 

Share this post


Link to post
Share on other sites

Try to lower the compression setting even more, and see if it helps.

As for the LibUsb drivers: you can only install them when the SPF device is in mini-monitor mode. Try to remove the Samsung drivers, switch the device into mini-monitor mode, and try to install the LibUsb drivers.

  • Like 1

Share this post


Link to post
Share on other sites

As for the LibUsb drivers: you can only install them when the SPF device is in mini-monitor mode. Try to remove the Samsung drivers, switch the device into mini-monitor mode, and try to install the LibUsb drivers.

 

Possible malfunctions my PhotoFrame. I removed the driver samsung PhotoFrame continues to work with the drivers LibUsb. As soon as I turn off the photo frame and then turn on again LibUsb driver no longer see her.

I also noticed that the Frame does not store the setting after turning off. For example install a brightness level of 100%, turn off - turn the brightness to 80%. It is also very often a window pops up with the demand to format the memory of the photo frame. I'll try to update the firmware hope this will fix the problem.

Share this post


Link to post
Share on other sites

Hello,

Would it be possible to grab the teamviewer capture/stream and display it to the lcd panel every x seconds ?

Idea is to watch on my photoframe my solar panels that is monitored using another laptop connected on the network.

I want to inspect the battery voltage drop while I use the inverter to run the PC to avoid going it too low.

Share this post


Link to post
Share on other sites

Hello,

Would it be possible to grab the teamviewer capture/stream and display it to the lcd panel every x seconds ?

Idea is to watch on my photoframe my solar panels that is monitored using another laptop connected on the network.

I want to inspect the battery voltage drop while I use the inverter to run the PC to avoid going it too low.

I'm afraid that type of usage is outside the scope of AIDA64. You could however request it as a new feature for Teamviewer.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Similar Content

    • By Roy
      Hi,
      it would be nice if there was the possibility to send sensor values unformatted as a number or percentage, via a serial port.
      Similar to the LCD displays, only without formatting, or pure numbers with separators.
      Together with a small GUI.
      Background is the simple evaluation of the data with a microcontroller and display in different ways.
      I imagine not only LCD or OLED, but rather seven segment display, nixi tubes or an analog pointer display. That would create a lot of possibilities.
    • By Wampo
      Hey Aida Team,
      i have some issues with this Adafruit LCD wich is recomended. On the two Pictures you can see what aida should do and what can i see on the Display. The First line is completely erased and the screen is flickering. The Adafruit Backpack is set to 20x4 LCD. When the Display is updating you can see the right setting for a millisecond.
      But if i change the LCD Setting in AIDA to 16x2, and leave the Backpack in 20x4 mode,  the Screen isn flickering and the first line is there. I think you got a little problem with the 20x4 Driver. I have Searched for the code but i cant find it, to edit it if i found the failure. 
       
      Please give me response for this BUG. I have extra ordert this overpriced 50€ LCD for it. 
      Greetings Daniel from Germany


      VID_20181129_160917.mp4
    • By Fiery
      We've added support for RoboPeak RPUSBDisp color graphical USB-connected LCD display.

      You can enable the LCD device from AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / RoboPeak. Currently there is no Windows driver made specifically for RoboPeak displays.  But there's a workaround: you can use the AlphaCool LCD driver (Version 2.1).  The driver installation has to be forced due to the USB device ID mismatch (between AlphaCool and RoboPeak displays).
      The driver installation works as:
      Open Device Manager --> Other devices --> double-click on rp-usbdisp --> Update Driver button --> Browse my computer for driver software --> Let me pick from a list of available drivers on my computer --> Show All Devices --> Next button --> Have Disk button --> Browse button --> select acusbdisplay.inf file from the AlphaCool LCD driver folder --> Next button --> press Yes button on the Update Driver Warning message box.

      You can order a RoboPeak display from DFRobot at:
      https://www.dfrobot.com/product-1062.html#.UqfXHfSnoqX
      You can find the new AIDA64 beta update at:
      https://www.aida64.com/downloads/latesta64xebeta
      Please let us know if you find any difficulties enabling or using this new feature. Also let us know if you've got another kind of LCD device that is currently unsupported by AIDA64.
      Regards,
      Fiery
    • By Fiery
      We've added support for several Matrix Orbital USB character based and monochrome graphical LCD displays, including LK, MX, PK, VK, GLK, GLT, GX Typhoon, and their drive-bay and external variants as well.
      You can enable the LCD device from AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD. The only thing needed to enable this feature is having the appropriate Matrix Orbital USB LCD drivers installed, and the LCD to be connected to a USB port. You can verify if your device is supported by AIDA64 by finding the device on the Devices / USB Devices page in AIDA64, and checking its Device ID. It should be one of the following IDs:
      0403-FA01
      0403-FA02
      0403-FA03
      0403-FA04
      0403-FA05
      1B3D-011F
      1B3D-0120
      1B3D-0121
      1B3D-0123
      1B3D-0125
      1B3D-0127
      1B3D-012C
      1B3D-0134
      1B3D-013E
      1B3D-013F
      1B3D-0140
      1B3D-0141
      1B3D-0155
      1B3D-0156
      1B3D-0157
      1B3D-0158
      1B3D-015E
      1B3D-0161
      1B3D-016A
      1B3D-016B
      1B3D-016C
      1B3D-0176
      1B3D-017B
      1B3D-01F0
      1B3D-01F1

      Due to their interface bottleneck BGK, EGLK, GLK and GLT displays perform display updates quite slowly, so visual discrepancies may be experienced when using the GLK (graphics) protocol on these displays. It is possible to use the LK (character based) protocol on GLK displays as well, which will work much faster. In order to switch between the GLK and LK protocols, you need to first disable the GLK protocol (in AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD), and then enable the LK protocol on the same page. Ignore the error, and restart AIDA64 to apply the switch.
      You can find the new AIDA64 beta update at:
      http://www.aida64.com/downloads/latesta64xebeta
      Please let us know if you find any difficulties enabling or using this new feature. Also let us know if you've got another kind of LCD device that is currently unsupported by AIDA64. BTW, Abacom, AlphaCool, Digital Devices, LCD2USB, Mad Catz Venom, and SDC Megtron LCDs are also supported now by the latest AIDA64 beta.
      Regards,
      Fiery
    • By Fiery
      We've added support for the built-in 160x32 pixel monochrome LCD screen of EVGA Z10 gaming keyboard.  You can enable the LCD device from AIDA64 / main menu / File / Preferences / Hardware Monitoring / LCD / EVGA.
      [/
      Currently AIDA64 communicates with the LCD directly, using USB HID interface.  It collides with EVGA's own software (EVGA Unleash), so it's recommended to close that software before enabling EVGA Z10 support in AIDA64.  EVGA will soon develop a proper SDK/API for their keyboard, much like the LCD API of Logitech gaming keyboards, so that multiple software can put information on the LCD the same time, without collisions.
      You can find the new AIDA64 beta update at:
      https://www.aida64.com/downloads/latesta64xebeta
      Please let us know if you find any difficulties enabling or using this new feature. Also let us know if you've got another kind of LCD device that is currently unsupported by AIDA64.
      Regards,
      Fiery
×
×
  • Create New...